Showing posts with label organization. Show all posts
Showing posts with label organization. Show all posts

Saturday, December 4, 2010

Punch Storage - Before and After

My old punch storage, a clear, over the door shoe holder, worked great.  It was accessible and I could see everything at a glance.  There were a few problems with it, though.  I outgrew it, there was no place to put my smaller punches and border punches, the weight of all the punches started to warp the door frame, and my closet door wouldn't close all the way.  Yikes!

The old way.

I really liked the rail system I saw other people using for their punches.  I searched all the local stores for cheap curtain rods, and ended up getting mine at Bed Bath & Beyond (with a coupon of course).  They are the BB&B brand 7/16" cafe rods that adjust from 28"-48" and were less than $5 each.  I was concerned about the weight of the punches on such a small diameter rod so I purchased extra brackets so we (thanks, wonderful hubby!) could install one on every stud, and they have held up really well.

The new way.  This looks so much neater.  And I'm a neat freak, so that is really important to me.  :)

The rods are spaced 6 " apart, and anchored every 18" on the studs.

The best part about this system is I can still expand the rods out to the next stud when I need to.  It looks like that will be happening soon, because I don't have any more room on these rods and I just ordered more punches.

Like I don't have enough already.

K

Friday, December 3, 2010

Ribbon Storage - Before and After

You may or may not have noticed how my ribbon was stored in my before picture.  I picked up two cardboard ribbon display holders from JoAnn's one year at the end of the holiday season.  They just gave them to me, and they were great for storing my ribbon.

Until I ran out of places to put them.

I could have painted them a pretty color, but that would have been too much trouble, and I always viewed them as a temporary storage solution.  They were fine until I could figure out how I wanted to store my growing supply of ribbon.

This was the old way.  I put SU ribbon in one holder, and all other brands in the other one.  Once I ran out of room, they ended up stacked in front of each other.  No matter which one ended up in front, I always needed what was in the back.  Ugh!  I had the cardboard holders, SU ribbon storage thingys, and jars with ribbon in them.  Nothing but a big mess!!  My ribbon needed some serious help.

When I use ribbon, I like to have the whole spool out.  Once I decide what ribbon I am going to use, I tie it to my project and cut it from the spool.  I hate to waste ribbon.  Almost as much as I hate to waste paper.  For that reason, using a dowel system would never work.  I would be forever removing and replacing spools.

I considered using a gutter (or three), but didn't have the wall space.

The pretty little boxes with grommet holes wouldn't work for the same reason as the dowels.

I even tried wrapping my ribbon around clothespins that was all the rage a couple years ago.  Boy am I sorry I wasted my time on that!  I didn't like that system at all.

I tried wrapping the ribbon around large flat spools like the ones you can use for embroidery thread.  Even though the ribbon wasn't wrapped tightly, it still came out with creases.

One option that was left was to go back to storing them in drawers like I did when I first started accumulating ribbon.  Sometimes you don't know how good a system is until you try everything else.  Since I was planning my own storage, I made sure to include what I needed for my ribbon.

One thing I like about storing them in drawers is that they are protected from light and dust.  With the ScrapNcube drawers, I can organize them by color, and I put a divider made out of foam board between the rows to keep them tidy.  This is a QB3 drawer.

This is what my ribbon looks like now.  It's so much nicer this way!

I underestimated how much room I needed for my ribbon, and need another drawer or two, but I love this way of storing my ribbon.  It is all together, protected from light and dust, and I can get to it very easily.

I put tiny tags of each color of ribbon on the drawer handles, so I can tell at a glance what drawer I need to open.

Since the SU grosgrain spools are so large, I have all of them stored in one of the larger drawers you can see in the above picture.

All in all, I am very happy with this way of storing my ribbon.  It is everything I want and nothing I don't.

Hope you have a great weekend!

K

Sunday, October 10, 2010

Making Progress

I have spent the last four days, almost entirely, in my craft room.  My ScrapNcube order arrived on Thursday, and my room wasn't even close to being ready.  I still needed to move most everything out and paint the trim.  Back track to 3 1/2 years ago when we first moved into this house.  In my haste to get my room together, I elected not to paint the trim.  I had painted the entire house, and couldn't bear the thought of painting the trim.  (Note to self - don't ever do that again.)  Right now, my craft room is the only room in the house that has painted trim.  And that makes me feel special.

I finished moving things out on Thursday, and prepped to paint.  I won't tell you that I elected (not forgot, but rather chose) not to caulk after I taped everything off.  Stupid!  (Note to self - don't ever do that again.)  Visions of the perfect room must have been clouding my brain, because I obviously wasn't thinking clearly.

Friday morning was spent painting the trim, and then we started moving things in.  My order came on 2 pallets, and it took almost as much work to get them unpacked as it did to put them together.  It took the entire day to get all my tables moved in and assembled.  I moved a few things in on Friday, but was so exhausted I had to get some sleep.  I wanted to sleep on my new tables, they were so pretty!  But that wouldn't have been very comfortable, so I went to bed instead.

I woke up early Saturday and started the big move-in.  I don't even think I made my coffee before I started.  I knew I hadn't ordered all the cubes I would eventually need, but I have a place for the things I use on a regular basis.  Once I decide how I want to store the left-overs, I'll know which cubes to order.  Moving all my paper out of my closet and into the file drawers has freed up a ton of shelf space in my closet, so now I have that storage space to use.


I can't tell you how happy Mr. Brown made me when he delivered my order.  This is one of two pallets.

Here is a peek at how I organized my embellishments.




Each color has a drawer of its own, with a few drawers having more than one color.  I tied a colored tag on each knob so I can see what color lives inside.


Here is a look at my orange and yellow embellishment drawer.  I decided to include my SU markers in my color drawers, and I'm not quite sure how that is going to work out. I'm going to give it a try, though, because that frees up other drawers I would otherwise use just for markers.


I have my ribbon stored in a similar way with colored tags on the knobs.  I love that my ribbon is now protected from the light (and dust).  It looks so much neater, too.


Here is my red, pink, orange, and yellow ribbon drawer.  I organized my ribbon with SU brand first, followed by other manufacturers for each color.  I was amazed at how much ribbon fit into each drawer.

I spent a good part of Saturday, and most of the day today unmounting and combining my stamps in SU storage cases.  My record is eleven sets in one case.  Granted, some of them are single stamps, but it would still take eleven boxes to store them, and I reduced that to one DVD sized case.  I'm not even close to seeing the light at the end of the tunnel, but if I do a few sets a day, I should be done in a couple months.  Just kidding - maybe a couple weeks.  I hope!


Here is a look at my record combination case.  It is the Extreme series and the Just (sports) series.  Eleven sets in one!!!

And that is why I don't have any pictures of my whole room yet.  It is still a mess with stamps, and cases, and stuff all over the place.  But I am making progress, and it looks so much better than it did.   I will try post pictures of my whole room soon.

Thanks for stopping by.  I hope you understand why I haven't been stamping lately.  That is going to change, though, now that I can get to all my stuff!

Toodles!

K

Monday, July 26, 2010

Getting Organized

A couple weeks ago, I passed a garage sale on my way home from work.  I found an old '70's dresser that was exactly what I was looking for to use as a sofa table.  It was in pretty good shape, and since it wouldn't fit in my car, I sent my husband back with his truck to pick it up.

He came home with TWO truckloads of stuff!  What?!  I thought we were trying to get rid of stuff!!!  But he was only thinking of me, and since he knew I wanted to get my craft room reorganized, he thought this massive sectional piece might work.  Isn't he awesome?

I finally got it moved in to my craft room, and it is, well, massive.  Not exactly what I was looking for, but the file drawers are just what I wanted to store my massive paper collection.

Shall I say massive again?

Massive.

Okay, I promise I won't say it any more.

Up until last night, I had all of my full pieces of cardstock stored together by SU! color families in cropper hopper bins in my closet.  All of my scraps were also stored by color families in hanging file folders in a file box that used to live in my closet.  I save all of my scraps, so the box was full!  This was a huge improvement over the 3 ring binders that I used to keep my scraps in.  But since there is no light in my closet, the box was on the floor and under a shelf,  I always had to pull the box out to see the color I wanted.  The file box eventually moved to a new home in the middle of my craft room.  And that wasn't working.

I came to the conclusion a while ago that it would be best to store my scraps and full sheets together.  Why go to two different places for the same thing?  Duh!  And it wasn't until hubby came home with that massive storage unit, that I could finally execute my plan.  I haven't even used any paper from my new system yet, but I know I am going to love it.


The top file drawer contains the brights, subtles, and regals collections.


The bottom drawer has the In Colors, neutrals, GKD and PTI cardstock, and all the other SU! cardstock.

Almost every hanging file folder has a full pack of cardstock plus a few full sheets and all my scraps for that color.  So there is more than enough room for my massive collection.  Oops, there I go again.  Sorry.


I used the file box to store all the retired SU! colors.  Each color already had a file folder with scraps, so I just slipped the full sheets in, and now I have them all together.  I am going to keep them for a while because I still like some of the colors.  I'll treat them like my clothes, though, and if I don't use them in the next year (or five!), they're gone!



Here is the space that I freed up in my closet.  I think I may use my empty bins for some of the craft magazines I save but never look at.  I do need a nice place to keep them!

Now I need a good way to store all my 12x12 papers. They are in the larger cropper hopper bins in my closet begging to be used.  You can see them peeking out at the bottom of the last picture.  How do you store your 12x12 papers?

I'm off to try out my new system...

K

Saturday, June 5, 2010

Foam Board Copic Storage


I'm back with the dimensions and directions for my Copic marker cubbies.

Supplies - foam board (1) 20" x 30"
                craft knife and extra blades
                quilting ruler(s) and cutting mat
                pencil
                hot glue gun and glue sticks (high temp)

outside dimensions - 14"H x 4 1/4"W x 5 1/2"D
side panels - 5 1/2" x 14" (cut 2)
shelves - 4 1/4" x 5" (cut 6)
top - 4 1/4" x 5 1/2" (cut 1)
bottom trim strip 1/2" x 4 1/8" (cut 1)

In order for the shelves to tilt back so the markers will stay in place, I offset the front and back measurements by 1/2".  The spacing between the shelves is 2 1/4".

Cut slots a little less than 3/16" wide and 5" long for the shelves to fit into on each side panel.  Remember to make the slots mirror images of each other.  Trim 3/16" of foam off the top edge for the top to fit into.

This is the right side panel.  The left side will be a mirror image.

Once all your slots are cut out, you can begin assembling.  Glue one shelf at a time onto one of the side panels.

This is the left side panel with the shelves in place.  Notice the top edge with the foam removed on the left side of the picture.  Doing this gives a nice finished look to the corners.

To attach the second side panel, I started each shelf about an inch into its slot, then ran a bead of glue in the remainder of each slot, and quickly slid the panel into place.  You must act quickly when glueing several edges at once.

Glue the top on, and if you want a finished look, a little trim strip on the bottom shelf.

Here are the finished cubbies.  (You can stop counting my Copics now.  heehee!  How do you know I don't have more?) 

I made two of these to hold all my Copics.  (As soon as I finished these, I ordered more.  Yes, I have a problem.)  Each shelf will hold 26 (maybe 27) sketch markers.  You could easily make it just a touch wider (1/2" wider would let you store 4 more markers on each shelf) to customize it to your marker collection.  I'm thinking I should have made mine bigger!

You may be able to make both cubbies out of one piece of foam board.  I used some scraps from my ink pad holder, and almost a whole new piece, so I'm not sure if it equals out.  I would buy 2 pieces to begin with, because I know you will want to make more projects!

Please see my foam board ink pad holder post for more details and tips.  If you make either one of these, or any other foam board projects, let me know.  I would love to see what you make!

And just because...  The content of this post is copyrighted by Karen Church, 2010.  Please feel free to use it to make your own projects, but please don't copy or sell it for your own profit.  Thanks.

Have fun!  Once you make one foam board project, you are sure to make more!

K

Friday, June 4, 2010

Foam Board Project Dimensions



Ok, ladies, here are my dimensions.

Ink Pad Holder

supplies needed - foam board (4 pieces) 20" x 30", 3/16" thick
                           craft knife and several extra blades
                           quilting ruler(s) and cutting pad
                           pencil
                           hot glue gun and glue sticks (high temp)
                           lots of patience!

outer dimensions -  15"H x 24"W x 5"D
shelves - 3 3/4"D x 24" L (cut 12 (or 13 if you don't need a taller space at the bottom for daubers))
vertical supports - 1 1/4" x 13 3/4" (cut 5)  This is the right measurement.  I didn't cut channels in the bottom of the top shelf, so they don't need to be 14" unless you cut the channels.
left and right sides - 5" x 15" (cut 2)
top and bottom - 5" x 24" (cut 2)
back - 15" x 24" (cut 1)

You can obviously customize this to make it bigger or smaller.  For each horizontal row, add or subtract 1"; for each vertical column, add or subtract 4".  All other measurements should stay the same.

The shelves aren't as deep as the outer sides because I wanted the edge of the ink pad to stick out a little from the shelf.  This leaves a little space between the pads and I think it makes it easier to remove them.

Using my quilting ruler, I drew pencil lines starting from one edge 3 3/4" long and 1" apart on each side panel.  (If you want to make the shelf on top to hold reinkers, cut the top slot all the way from the front to the back.  This is where the 'top' piece goes.  If you don't want the top shelf, make your sides 1" shorter.)  Then I cut a slot with a craft knife a little less than 3/16" wide centered over each line.  This allows for a snug fit, and in my opinion, requires less glue to hold it together.  You can 'feel' how deep you make the cut, and just don't want to go through the back side of the foamboard.    Once my slots were cut, I used a jewelry tweezer to slide along the bottom of the foam to remove it from the back side of the paper.  You could use a small flat head screwdriver to do this, but I was lazy and didn't want to go to the garage to find one.  Anything that is dull and about 3/16" wide will work.  You can test your first slot by sticking the shelf in it to see how snug the fit is.  Then adjust your slot width if necessary.  Also make sure you mark your lines as mirror images on each end panel.  I made the mistake of marking them the same and had to re-do it.


See how the side panels are mirror images of each other?  The top slot goes all the way from front to back for the top to fit into.  I also trimmed 3/16" of foam from the bottom edge of each panel for the bottom to fit into.

I used my quilting ruler as a guide when cutting with the craft knife which makes it really easy to line everything up.  I tried a rotary cutter, and it didn't work, so craft knife it was.  You will go through several blades as they tend to dull quickly.  If you find that the foam pulls a little, and you aren't getting a clean cut, it's time to get a new blade.  I used at least 3 blades for this project.

Now it is time to cut holes in the shelves for the vertical supports to fit through.  The supports are a little less than 4" apart.  (This is because the end of each shelf goes into slots on the side panels 3/16" on each end.)  I measured my center line first - 12" from one end, then measured a tiny bit less than 4" for each of the other supports.  Each slot is 1 1/4" long and a little less than 3/16" wide and centered in the shelf (1 1/4" from both the front and back).  This time you will want to cut all the way through the foam board to make a hole.  This is where the first dose of patience comes in.  It takes a long time to cut those 60 little holes!

You will need to cut holes in the bottom panel in the same way.  Just start the slot 1 1/4" from the back edge, and they will all line up.

The holes are centered on each shelf, but are 1 1/4" from the back edge of the bottom panel.  See how they will all line up when assembled?

Now summon up some courage and patience, because it is time to start assembling.  This is the most rewarding part, though, and you will be so excited when you see it start to take shape!

I did a dry run first, without hot glue, just to make sure it was going to fit together.  Once I was satisfied with a few shelves in place, I disassembled it and started over with hot glue.  I used a high heat glue gun.  You have to act quickly, and have a few fractions of a second more to work with when you use high heat vs. low heat.  You could try a low heat gun if you already have it, but even the high heat started to set before I was ready toward the end of assembly.

Working one at a time, place a small bead of glue around the very bottom of each vertical support strip, and place into the slots on the bottom panel.  (Be sure to lift it up after every time to make sure you don't glue your project to the table.  Don't ask me how I know to do that!)

This is what you should have at this point.

Now it is time to slide each shelf onto the supports.  I tested most of the slots in the shelf, but if they are a little tight, just take it slow and easy pushing them down.  After you get each shelf in place, measure all the way around to make sure it is level.  Making sure they are evenly spaced is very important!  I used the end panels as a guide for placement. Then run a small bead of glue around the vertical support/shelf junction.  Add one shelf at a time, making sure it is spaced correctly before glueing.

Here, I have used the end panels as a spacing guide.  Do not glue the end panels in place yet.  You will do that after all the shelves are in place.

Continue adding shelves until they are all on the vertical supports.  Here is where you will need your second dose of patience.  You are going to glue each end panel on the shelves, and you must act very quickly once you apply the hot glue.  I started each shelf about an inch or so into its corresponding slot, quickly ran a bead of glue in all the remaining slot areas, then carefully slid the panel the rest of the way onto the shelves.  Do this for both end panels.

Now you will be ready to attach the top.  I put glue in each end panel slot and on the top of each vertical support, and set the top in place.  The front strip on the little top shelf measures 7/8" x 23 5/8".  Glue it in place, and all that is left is the back panel.

I glued the back on in two steps by running glue on one side edge and only halfway across the top and bottom edges before putting the back in place.  Then I ran glue on the remaining edges to attach the remaining half.


Ta-da!  Wasn't that fun?  You should be proud of yourself.  I know I was!

If you run into any problems, or can't make sense of my directions, please let me know and I will try to help.

And just because, I have to say this...  This is my own original design, including the measurements and directions.  Please feel free to use it to make your own projects, but please don't copy or sell it for your own profit.  Thank you.

I will be posting directions for my Copic marker cubbies next, and they are a lot less complicated.  If you are going to make both, I would start with the Copic cubby, then tackle the ink pad holder.

Guess I should have posted directions for them first.  What was I thinking?!  Sheesh!

Thanks again for your interest, and I'll be back soon with Copic cubby directions.

K

Monday, May 31, 2010

Copic Marker Storage

Edited:  For more detailed directions regarding my foam board projects, please see my post here.  It gives some general tips for cutting, etc.  If you want to see all my posts regarding foam board projects, click on the "foam board" label on the left sidebar of my blog.  Thanks!



After I posted my last entry, I was sitting there feeling sorry for myself, and was trying to think of something I could do to make myself feel better.  Then I remembered Patter's post last Friday about her new Copic storage that she purchased from Studio 3 Solutions.  I love her organizational ideas, and thought this would be a great foam board project for me to make.

I have been using a photo box that I put cardboard dividers in to store my Copic markers.  It was inexpensive, and works pretty well, but every time I want to use a marker, I have to drag the whole box down off the shelf, find a place to put it on my work table (which is next to impossible), then put it back when I am done.  I almost always find a stray marker after I'm done and have to get the box down and put it back again.



My cheap storage wasn't working for me any more, and was in need of a makeover.

Foam board to the rescue!!!

After making my ink pad holder, I had a better idea of what I was doing, and this project only took a couple of hours.  I angled the shelves down toward the back so the markers would stay in place.  Like before, I made channels for the shelves to fit into.

I hot glued the shelves to one side, then put hot glue in all the channels of the second side and quickly attached it to the shelves that were already in place.  I added top and back pieces, and my project was finished.


Doesn't this look much better?  I love how all my markers will be at my finger tips instead of lugging that box off the shelf every time.  And when I reorganize my room, I can stack them vertically if I want.

I have 26 markers in one of the shelves, and could possibly fit one more in there if I needed to.  These two cubbies could hold over 300 sketch markers.  I doubt I will ever have that many, but I still have a lot of room to grow.

Patter's storage cubbies cost $16.95 each.  I was able to use some of the left over foam board from my ink pad storage, plus most of a whole new 20" x 30" piece.  I figured mine cost less than $2.00 for both cubbies since I bought the foam board when it was 50% off.  That is a savings of  $31.90 plus S&H.

I'll add that to my piggy bank for the Scrap 'n Cube storage I am pining for!

I'm not feeling so bad about losing my mojo after all!

K

Thursday, May 27, 2010

Quest For Simplification

Recently, I have been thinking a lot about reorganizing my craft room and simplifying the card making process.  I say thinking, because there has been very little action.  That is only because I am a perfectionist, and it has to be perfect when I finally do it.  And I can't decide what I want.  It's kind of like shopping for toothpaste.  Why can't you buy regular toothpaste anymore?  It worked just fine for me during my childhood.  Plain ol' Crest or Colgate in a tube.  Why did they have to stop making it and come up with all this other anti-plaque, cavity fighting, whitening, breath freshening, blah, blah, blah?  Isn't that what toothpaste is supposed to do?  Sorry for my digression.  But I feel better now.

A few weeks ago while 'thinking' about my room and supplies, I had a "Duh!" moment.  I decided to cut a whole bunch of card bases so they would always be ready when I wanted to make a card.  Now, it doesn't take a rocket scientist to figure out that this simplifies the process.  I am just wondering why it took me so long to think of doing it.  Especially since the paper I use for my card bases is the only thing I use that particular paper for.  It's just common sense.  Something I pride myself for having a good amount of.  It's embarassing to think it took me so long to figure it out.

So now I have a neat little stack of card bases sitting on my work table, and it is so nice to have them at the ready.

I just have to figure out where I am going to store them!

~K

Friday, May 14, 2010

Foam Board Ink Pad Holder



I am on a reorganizing kick in my craft room.  I have 5 of the acrylic Dzyntec storage cubes that I have been using for many years.  I really like them because they store 12 ink pads, and there are three little drawers that are divided into 12 compartments.  I store my reinkers, daubers, and matching brads in them.  There is also a drawer to hold markers.  Basically, every color family has it's own little container, and I love having it all together.  But they take up a lot of room.

I was looking through the SCS galleries for a new way to store my ink pads, and I came across wenchie's gallery.  She has a variety of holders and storage items that she has made out of foam board, and I thought I would give it a try.  I really liked the clean lines of them, and it would be really cheap.

If you're wondering why I haven't been stamping lately, it's because I have spent days making my ink pad holder.  Being a perfectionist has its drawbacks, but it also pays off with a project like this.  Figuring out the dimensions probably took as long as it did to make it, but now that I know what I am doing, I can see myself making other projects in the future.

I cut all the pieces using my quilting rulers and a craft knife. Then I cut the end pieces where the shelves will go.  I was careful to not cut all the way through the back paper so the foam could be removed, creating the slots.


I also cut holes in each shelf and the bottom for the vertical supports.  Measure four times, cut once.  That's why it took me so long, but I never made a mistake!


I started the assembly by hot gluing the vertical supports into the base.  If you do this, make sure you lift it off of your work surface before the glue sets so it doesn't get stuck!


I checked the shelf height with the end pieces temporarily in place.  Then I put a little line of hot glue around the vertical supports.  Most of the slots were cut to fit pretty snug, so a lot of gluing wasn't necessary.


Starting the next shelf.


Shelf pushed all the way down the supports.  My shelves were spaced 1" on center, so it was easy to line them up using my quilt ruler.  As soon as I got the shelf in place and level, I ran a little bead of hot glue around the vertical support.  (No, I did not use a carpenter's level, I just eyeballed it with the ruler!)  Each shelf was done in this manner.


Ta-da!  After all the shelves were in place, I glued on the ends, top, and back.  The top is a shelf to hold all my reinkers.


Here it is with some of my SU! ink pads.  The reinkers are all on top, my markers will fit in one of the slots, and my daubers fit perfectly on the bottom shelf in the Dzyntec acrylic holders.  I still have room for the 10 In Colors, and any extra ink pads I want to hold on to.  The best thing is that this has a much smaller footprint than the 4 Dzyntec holders everything was in before.  Only the brads need a new home, and I'm working on that one. 

I am really pleased with how this turned out.  Now I just need to make another one for all my Staz-on and various other ink pads.

I think I'll stamp something first, though!

K

ETA:  For more detailed directions and the dimensions I used, see my other post here.  To see all of my foam board projects, you can click on the "foam board" label on the left side of my blog.